1. #1
    Just updated from OOB 303m to 404m. Paid attention to D/L in correct order. All works except the aircraft are all uncontroalable. All control inputs are working, but I will eventually loos control. I had this problem when I first started and received in correct parameters to enter in the config file which are as follows:

    X=0 1 4 9 16 25 36 49 64 81 100 0
    Y=0 1 4 9 16 25 36 49 64 81 100 0
    Z=0 10 20 30 40 50 60 70 80 90 100
    RZ=0 10 20 30 40 50 60 70 80 90 100 0
    FF=0
    U=0 10 20 30 40 50 60 70 80 90 100 0
    V=0 10 20 30 40 50 60 70 80 90 100 0
    1X=0 0 0 0 13 30 46 59 70 84 100 0
    1Y=0 0 0 0 13 30 46 59 70 84 100 0
    1Z=0 35 41 48 56 67 76 82 89 95 100 0
    1X1=0 13 21 28 39 53 65 77 88 96 100 0
    1Y1=0 22 28 37 45 54 65 77 88 97 100 0
    1RX1=0 10 20 30 40 50 60 70 80 90 100 0
    1RZ1=0 100 100 100 100 100 100 100 100 100 100 0
    1U1=0 100 100 100 100 100 100 100 100 100 100 0
    1V1=0 100 100 100 100 100 100 100 100 100 100 0

    I use the Saitek 45 with CH pedals
    QUESTION: Has this now changed with the updates?

    and Ideas ?

    Denis
    Share this post

  2. #2
    Just updated from OOB 303m to 404m. Paid attention to D/L in correct order. All works except the aircraft are all uncontroalable. All control inputs are working, but I will eventually loos control. I had this problem when I first started and received in correct parameters to enter in the config file which are as follows:

    X=0 1 4 9 16 25 36 49 64 81 100 0
    Y=0 1 4 9 16 25 36 49 64 81 100 0
    Z=0 10 20 30 40 50 60 70 80 90 100
    RZ=0 10 20 30 40 50 60 70 80 90 100 0
    FF=0
    U=0 10 20 30 40 50 60 70 80 90 100 0
    V=0 10 20 30 40 50 60 70 80 90 100 0
    1X=0 0 0 0 13 30 46 59 70 84 100 0
    1Y=0 0 0 0 13 30 46 59 70 84 100 0
    1Z=0 35 41 48 56 67 76 82 89 95 100 0
    1X1=0 13 21 28 39 53 65 77 88 96 100 0
    1Y1=0 22 28 37 45 54 65 77 88 97 100 0
    1RX1=0 10 20 30 40 50 60 70 80 90 100 0
    1RZ1=0 100 100 100 100 100 100 100 100 100 100 0
    1U1=0 100 100 100 100 100 100 100 100 100 100 0
    1V1=0 100 100 100 100 100 100 100 100 100 100 0

    I use the Saitek 45 with CH pedals
    QUESTION: Has this now changed with the updates?

    and Ideas ?

    Denis
    Share this post

  3. #3
    Add a 0 to the end of the Z line there. That will help some, but I'm guessing a large part of your problem is just not being used to the large flight model changes between 3.03 and 4.04. Give it some time and you should adjust.
    Share this post

  4. #4
    Can't tell from those numbers which is for the X-45 and which is for the pedals.

    You may wan't to try the utility in my sig, it'll make it much easier for you to change them settings... It does come with some profiles, you can just try 'm...

    Oh, and surely what the MonkeyH said: It needs time to get used to, but it does start with correct sensitivity settings... (As in: well, not too extreme ones. Me thinks: 1X=0 0 0 0 13 30 46 59 70 84 100 0 is a bit extreme)

    Have Fun!
    Share this post

  5. #5
    Thanks for the quick replies: Monkey maybee your right, I wasn't aware the flight models had changed: and "Fool" thanks I will certainly look over your sig


    Denis
    Share this post

  6. #6
    steve_v's Avatar Senior Member
    Join Date
    Apr 2002
    Posts
    7,895
    your rudder/pedals seem extreme

    1Z=0 35 41 48 56 67 76 82 89 95 100 0


    yaw and pitch seem resonable at

    1X1=0 13 21 28 39 53 65 77 88 96 100 0
    1Y1=0 22 28 37 45 54 65 77 88 97 100 0

    you might want to review http://www.airwarfare.com/tech/sticks.htm
    Share this post

  7. #7
    Don't know if this will help, but here is mine.

    Not a 45, but a 52 with Ch pedals. Maybe a little agressive for an X-45, but it's a place to start.

    [rts_joystick]
    X=0 1 4 9 16 25 36 49 64 81 100 0
    Y=0 1 4 9 16 25 36 49 64 81 100 0
    Z=0 10 20 30 40 50 60 70 80 90 100 0
    RZ=0 10 20 30 40 50 60 70 80 90 100 0
    FF=0
    U=0 10 20 30 40 50 60 70 80 90 100 0
    V=0 10 20 30 40 50 60 70 80 90 100 0

    1X1=0 65 72 79 86 93 100 100 100 100 100 0..............Aileron
    1Y1=0 65 72 79 86 93 100 100 100 100 100 0..............Elevator
    1Z1=0 100 100 100 100 100 100 100 100 100 100 0.........Throttle
    1Z=0 72 78 83 87 93 96 99 100 100 100 0.................Rudder
    1RY1=0 1 4 7 13 20 29 40 52 66 81 0.....................Trim Aileron
    1U1=0 1 2 4 10 14 21 29 37 47 53 10.....................Trim Elevator
    1RX1=0 1 4 6 11 16 23 32 42 53 66 0.....................Trim Rudder
    1Y=1 0 0 0 13 38 64 88 100 100 100 0....................Brakes
    Share this post