PDA

View Full Version : Valves to reduce water pressure!!!!



eskimosound
07-30-2019, 05:24 PM
Are you sure?
What's the sequence guys it's driving me mad I can't see any logic to it ..

Finland_Jami
07-30-2019, 05:29 PM
i just checked what had pipe connect the them

GameZone_GaMinG
07-30-2019, 05:36 PM
https://www.youtube.com/watch?v=Vk7iE95cmI0&t=3s

Sprayz_the_Area
07-30-2019, 05:37 PM
There are 3 valves that have a hazard like paint job over them. (Yellow and black) and 3 that don't. Choose the 3 that has the Hazard paint

Jim_867_5309
07-30-2019, 05:55 PM
Just follow the pipe line. start from the furthest away from the valve and flip them till you get to the valve.

Abarth_71
07-30-2019, 06:40 PM
Follow the pipe.

SamanthaMarcus
07-30-2019, 07:00 PM
Are you sure?
What's the sequence guys it's driving me mad I can't see any logic to it ..

Only the ones with black n yellow striping on

eskimosound
07-31-2019, 01:45 AM
I've done it through pot luck, utter nonsense, in fact the whole mission is, there's no guidance, go here, go there do this.......go where, do what... seriously.....Kenly is terrible, go back to the echo? I mean come on get 3 missions out of 1 echo...poor, poor...very poor.

GetMused
07-31-2019, 03:16 AM
Yeah Iím not a fan of kenley at all... and when you compare episode one to the activities in d1, itís even worse.

Really, we had survival, underground and resistance. To me thereís no comparison.

I really hope episode 2 brings survival back. That mode was epic and groundbreaking

tracertong666
07-31-2019, 03:28 AM
Probably the worst mission ever created in the history of The Division. C'mon guys you can do better than this garbage ?

tcarlisle2012
07-31-2019, 03:47 AM
Yeah, that one is a little tricky. Look at the switch that is guides you too first. Notice it has yellow and black stripes surrounding that switch. Flip that switch, and then all the others that have the same yellow/black surrounding.

Edgemoor
07-31-2019, 08:05 AM
You need to follow the pipe around the room. It's easier from one of the catwalks that are elevated, you can see when the pipe branches off. Where it branches, is where one of the switches are. These are the switches that need to be flipped.

Once you figure it out it's actually really easy, just not obvious because your vantage point is from the ground.

John_Wick117
07-31-2019, 12:05 PM
The kenly missions are quite simple, the power part in the metro it shows what fuse to engage on the monitor screens where you activate the power button, the water pressure part also shown with the yellow and black however i am really color blind so did not really see that part of it so other people have a bit of an advantage over me :P i just did a trial and error thing.

I do not mind the bit of extra time that is required for those area's.

Riflemania
07-31-2019, 12:09 PM
I blagged it

eskimosound
07-31-2019, 11:12 PM
In a nutshell, turn the wheel valve, then in front of you (behind the wheel valve if you are looking into the centre of the room) there is a red handled valve against yellow and black chevrons, turn that then go to the valve that's marked (left hand side further into the room) then turn the next valve that's marked..then go back to the wheel valve....
It's finding that first valve that sends you mad.

dagrommit
07-31-2019, 11:18 PM
You can tell you've turned the correct valve by listening to the sound. A full gushing sound indicates it's the right one. A quieter one indicates it's not.