PDA

View Full Version : Ordered CH Pro Pedals USB, may need some help with setup.



wildcat101
06-28-2004, 01:31 PM
Guys,
I ordered some Ch Pro Pedals USB, and could use some advice when I go to set them up. I have a MSFFB2 joystick. Any tips, advice would be appreciated.

wildcat101
06-28-2004, 01:31 PM
Guys,
I ordered some Ch Pro Pedals USB, and could use some advice when I go to set them up. I have a MSFFB2 joystick. Any tips, advice would be appreciated.

|CoB|_Spectre
06-28-2004, 01:34 PM
Wildcat, welcome to the world of quality flight control peripherals. Your best place to get help for CH Products stuff is Revvin's outstanding website at www.ch-hangar.com/forum (http://www.ch-hangar.com/forum) in which you will find more helpful people and posts than ever imagined.

RocketDog
06-28-2004, 01:41 PM
V. Important Point!

The pedals will be taken as input device 1 and the FFB stick as input device 2. The sliders for setting sensitivity in the GUI won't work and you will end up with a very sensitive stick around the central position in boith pitch and roll. The solution is to edit the sensitivity in the conf.ini file. Here is what I use:

[rts_joystick]
X=0 1 4 9 16 25 36 49 64 81 100 0
Y=0 1 4 9 16 25 36 49 64 81 100 0
Z=0 10 20 30 40 50 60 70 80 90 100
RZ=0 10 20 30 40 50 60 70 80 90 100 0
FF=0
U=0 10 20 30 40 50 60 70 80 90 100 0
V=0 10 20 30 40 50 60 70 80 90 100 0
1X=0 1 4 9 16 25 36 49 64 81 100 0
1Y=0 1 4 9 16 25 36 49 64 81 100 0
1RZ=0 100 100 100 100 100 100 100 100 100 100 0
1U=0 100 100 100 100 100 100 100 100 100 100 0
1V=0 100 100 100 100 100 100 100 100 100 100 0
1X1=0 1 4 9 16 25 36 49 64 81 100 0
1Y1=0 10 20 30 40 50 60 70 80 90 100 0
1Z1=0 4 7 12 17 28 38 50 68 85 100 0
1X2=0 100 100 100 100 100 100 100 100 100 100 0
1Y2=0 100 100 100 100 100 100 100 100 100 100 0
1RX2=0 100 100 100 100 100 100 100 100 100 100 0
1RZ2=0 100 100 100 100 100 100 100 100 100 100 0
1U2=0 100 100 100 100 100 100 100 100 100 100 0
1V2=0 100 100 100 100 100 100 100 100 100 100 0
1Z=0 100 100 100 100 100 100 100 100 100 100 0
1RX1=0 100 100 100 100 100 100 100 100 100 100 0
1RZ1=0 100 100 100 100 100 100 100 100 100 100 0
1U1=0 100 100 100 100 100 100 100 100 100 100 0
1V1=0 100 100 100 100 100 100 100 100 100 100 0


Here 1X1 and 1Y1 (or maybe even 1X and 1Y, can't remember) are the sensitivity settings for the stick roll and pitch axes. You can easily check which it actually is by setting a row to zeros all across and popping into the QMB. The control axis set to zero will not respond as you waggle the stick.

I think Hunter or Tully have explained it better elsewhere, but after three glasses of wine for dinner this is frankly as good an explanation as you will get from me until tomorrow.

Regards,

RocketDog.

wildcat101
06-29-2004, 10:41 AM
Thanks guys for the excellent answer. Should have them tomorrow hopefully.

Mark